Exit Zen
61
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/ListInterfacesParameterWrapper.cs:14
English
This parameter returns a packed list of network interface descriptors, representing the IPv4 network interfaces on the device.
62
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/ReleaseDHCPLeaseParameterWrapper.cs:10
English
Release DHCP Lease
63
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/ReleaseDHCPLeaseParameterWrapper.cs:11
English
This parameter causes the device to release its DHCP address.
64
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/IPv4DefaultRouteParameterWrapper.cs:13
English
IPv4 Default Route
65
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/IPv4DefaultRouteParameterWrapper.cs:15
English
This parameter is used to get and set the default IPv4 route for a device. The default route is a global property of a device. If a default route exists, it may point to a gateway or, in the case of a point - to - point link, to an interface without a gateway. If a gateway is used, the device may be able to provide the interface the gateway is reachable on. This is extra information which may facilitate debugging, but devices are not required to provide it.
66
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/DHCPParameterWrapper.cs:10
English
DHCP
67
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/DHCPParameterWrapper.cs:12
English
This parameter is used to retrieve or change the Dynamic Host Configuration Protocol [DHCPv4] mode for an interface. Changes to the DHCP mode will not take effect until the Interface Apply Configuration message is received by the interface.
68
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/IPv4StaticAddressParameterWrapper.cs:10
English
IPv4 Static Address
69
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/IPv4StaticAddressParameterWrapper.cs:12
English
This parameter is used to statically configure the IPv4 address and network mask on an interface. Changes to the IPv4 Static Address will not take effect until the Interface Apply Configuration message is received by the interface.
70
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/DNSDomainNameParameterWrapper.cs:11
English
Domain Name
71
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/DNSDomainNameParameterWrapper.cs:12
English
This parameter is used to get and set the unqualified domain name for a device.
72
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/HardwareAddressParameterWrapper.cs:10
English
Hardware Address
73
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/HardwareAddressParameterWrapper.cs:11
English
This parameter is used to fetch the MAC address of an interface.
74
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/RenewDHCPLeaseParameterWrapper.cs:10
English
Renew DHCP Lease
75
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/RenewDHCPLeaseParameterWrapper.cs:11
English
This parameter causes the device to attempt to renew its DHCP address.
76
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/IPv4NameServerParameterWrapper.cs:10
English
IPv4 Name Server
77
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/IPv4NameServerParameterWrapper.cs:11
English
This parameter is used to set the IPv4 DNS name servers for a device. Up to three IPv4 name servers may be configured.
78
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/ZeroconfModeParameterWrapper.cs:10
English
Zeroconf Mode
79
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/ZeroconfModeParameterWrapper.cs:12
English
This parameter is used to retrieve or change the IPv4 Link Local Addressing (Zeroconf) [IPv4LL] mode on an interface. Changes to the Zeroconf mode will not take effect until the Interface Apply Configuration message is received by the interface.
80
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/DNSHostNameParameterWrapper.cs:11
English
Host Name