Exit Zen
73
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/HardwareAddressParameterWrapper.cs:11
English
This parameter is used to fetch the MAC address of an interface.
74
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/RenewDHCPLeaseParameterWrapper.cs:10
English
Renew DHCP Lease
75
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/RenewDHCPLeaseParameterWrapper.cs:11
English
This parameter causes the device to attempt to renew its DHCP address.
76
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/IPv4NameServerParameterWrapper.cs:10
English
IPv4 Name Server
77
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/IPv4NameServerParameterWrapper.cs:11
English
This parameter is used to set the IPv4 DNS name servers for a device. Up to three IPv4 name servers may be configured.
78
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/ZeroconfModeParameterWrapper.cs:10
English
Zeroconf Mode
79
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/ZeroconfModeParameterWrapper.cs:12
English
This parameter is used to retrieve or change the IPv4 Link Local Addressing (Zeroconf) [IPv4LL] mode on an interface. Changes to the Zeroconf mode will not take effect until the Interface Apply Configuration message is received by the interface.
80
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/DNSHostNameParameterWrapper.cs:11
English
Host Name
81
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/DNSHostNameParameterWrapper.cs:12
English
This parameter is used to get and set the unqualified host name for a device.
82
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/ApplyInterfaceConfigurationParameterWrapper.cs:10
English
Apply Interface Configuration
83
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/ApplyInterfaceConfigurationParameterWrapper.cs:12
English
This parameter applies the stored configuration to an interface. The configuration of an interface shall include, but is not limited to, the settings in IPV4 Static Address, IPV4 DHCP Mode(if supported) and IPV4 Zeroconf Mode(if supported).
84
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/IPv4Address_NetmaskParameterWrapper.cs:10
English
IPv4 Address / Netmask
85
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/IPv4Address_NetmaskParameterWrapper.cs:11
English
This parameter is used to retrieve the current IPv4 Address and Netmask information for an interface.
86
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/InterfaceNameParameterWrapper.cs:10
English
Interface Name
87
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-2/InterfaceNameParameterWrapper.cs:11
English
This parameter is used to retrieve the label for a network interface.
88
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-1/DMX512StartupModeParameterWrapper.cs:10
English
DMX512 Startup Mode
89
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-1/DMX512StartupModeParameterWrapper.cs:12
English
This parameter defines the behavior of the device when it starts up and the DMX512 control signal is absent. The DMX512 signal is considered absent when standard DMX packets are not received for a period of greater than 1.25 seconds.
90
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-1/ModulationFrequencyDescriptionParameterWrapper.cs:11
English
Modulation Frequency Description
91
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-1/ModulationFrequencyDescriptionParameterWrapper.cs:13 ../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-1/OutputResponseTimeDescriptionParameterWrapper.cs:13
English
This parameter is used to get a descriptive ASCII text label for a response time setting. The label may be up to 32 characters.
92
../DMXLIB/RDM/ParameterWrapper/Catalogue/E1.37-1/DMX512BlockAddressParameterWrapper.cs:10
English
DMX512 Block Address